Search Results

The maximum extent of liquid-phase fuel penetration into in-cylinder gases is an important parameter in compression-ignition (CI) engine design. Penetration of the fuel is needed to promote fuel-air mixing, but over-penetration of the liquid phase and impingement on the bowl wall can lead to higher emissions. This maximum liquid-phase fuel penetration, or “liquid length,” is a function of fuel properties, in-cylinder conditions, and injection characteristics. The goal of this study was to measure and correlate the liquid lengths of fuels with wide physical property variations. The fuels were injected into a large range of in-cylinder temperature (700 to 1300 K) and density (3.6 to 59.0 kg/m3) conditions, at an injection pressure (140 MPa) that is characteristic of those provided by current high-pressure injection equipment.

Two-dimensional pulse-laser Mie scattering visualization of the direct-injection gasoline fuel sprays and wall impingement processes was carried out inside a single-cylinder optically accessible engine under motoring condition. The injectors have been first characterized inside a pressurized chamber using identical technique, as well as high-speed microscopic visualization and phase Doppler measurement techniques. The effects of injector cone angle, location, and injection timings on the wall impingement processes were investigated. It was found that the fuel vaporization is not complete at the constant engine speed tested. Fuel spray droplets were observed to disperse wider in the motored engine when compared with an isothermal quiescent ambient conditions. The extent of wall-impingement varies significantly with the injector mounting position and spray cone angle; however, its effect can be reduced to some extent by optimizing the injection timing.

Experiments were conducted on a single cylinder engine to measure the ionization current across the spark plug electrodes as a function of key operating parameters including air/fuel ratio. A unique ignition circuit was adapted to measure the ion current as early as 300 microseconds after the initiation of spark discharge. A strong relationship between air/fuel ratio and features of the measured ion current was observed. This relationship can be exploited via relatively simple algorithms in a wide range of electronic engine control strategies. Measurements of spark plug ion current for approximating air/fuel ratio may be especially useful for use with low cost mixture control in small engine applications. Cylinder-to-cylinder mixture balancing in conjunction with a global exhaust gas oxygen sensor is another promising application of spark plug ion current measurement.

We have prepared and tested laboratory scale monoliths wash-coated with 10, 20 and 30 wt% of either CeO2 or Ce.75Zr.25O2 (remainder is alumina). Wet impregnation was used to load the wash-coated monoliths with 50g/ft Pt:Rh at a 5:1 ratio. The catalyst were aged at temperatures between 825°C and 950°C using a cycled redox aging. The catalysts were then tested in a full-feed simulated exhaust laboratory reactor with air-to-fuel ratio (A/F) perturbations (frequencies at 1 and 3 Hz and amplitudes up to +/- 0.8 A/F). Even the lowest loading of Ce.75Zr.25O2 outperformed all three loadings of CeO2 over a full range of reaction temperatures, A/F perturbations, and catalyst space velocity (SV). Our data indicates that the ceria-zirconia catalysts can tolerate cycled redox aging at sustained bed temperatures at least 25°C higher (∼925°C vs. < 900°C) than can ceria. For the CeO2 catalysts aged at or above 900°C we observed an inverse correlation of catalyst activity to CeO2 loading.

The current extensive revisitation of the application of gasoline direct-injection to automotive, four-stroke, spark-ignition engines has been prompted by the availability of technological capabilities that did not exist in the late 1970s, and that can now be utilized in the engine development process. The availability of new engine hardware that permits an enhanced level of computer control and dynamic optimization has alleviated many of the system limitations that were encountered in the time period from 1976 to 1984, when the capabilities of direct-injection, stratified-charge, spark-ignition engines were thoroughly researched. This paper incorporates a critical review of the current worldwide research and development activities in the gasoline direct-injection field, and provides insight into new areas of technology that are being applied to the development of both production and prototype engines.

A novel approach is presented to the problem of robust control strategy for an Exhaust Gas Recirculation (EGR) system. Modeling issues and controller design for an electric valve are presented. Robustness is one of the main issues due to nonlinearities (hysteresis, friction), computational time delays, and the effects of complex exhaust gas dynamics. A high level of noise, due to engine vibrations, makes the input-output model identification very difficult. We use a special windowing technique to successfully complete the identification. It was found that a good approximation of the system dynamics consists of a first order transfer function with a time delay whose parameters depend on the operating conditions (engine load, r.p.m.). Thus, the nonlinear effects of friction and hysteresis are replaced, for the purpose of control design, by variable gain, time delay, and time constant of the linear model.

Video imaging has been used to investigate the evolution of liquid fuel films on combustion chamber walls during a simulated cold start of a port fuel-injected engine. The experiments were performed in a single-cylinder research engine with a production, four-valve head and a window in the piston crown. Flood-illuminated laser-induced fluorescence was used to observe the fuel films directly, and color video recording of visible emission from pool fires due to burning fuel films was used as an indirect measure of film location. The imaging techniques were applied to a comparative study of open and closed valve injection, for coolant temperatures of 20, 40 and 60 °C. In general, for all cases it is shown that fuel films form in the vicinity of the intake valve seats.

An experimental study was made to investigate the spray characteristics of high pressure fuel injectors for direct-injection gasoline engines. The global spray development process was visualized using two-dimensional laser Mie scattering technique. The spray atomization process was characterized by Phase Doppler particle analyzer. The transient spray development process was investigated under different fuel injection conditions as a function of the time after the fuel injection start. The effects of injector design, fuel injection pressure, injection duration, ambient pressure, and fuel property on the spray breakup and atomization characteristics were studied in details. Two clear counter-rotating recirculation zones are observed at the later stage or after the end of fuel injection inside the fuel sprays with a small momentum. The circumferential distribution of the spray from the large-angle injector is quite irregular and looks like a star with several wings projected out.

Ionization probes built into the head gasket and uniformly distributed around the cylinder bore of a knocking, spark-ignition engine have been used to locate the autoigniting end-gas region. As normal combustion evolves after spark ignition, the ionization probes individually respond to the arrival of the propagating flame. Then, when autoignition occurs, the probes located in the end-gas region respond in rapid succession. By utilizing pressure transducer measurements to determine when autoignition occurs, the ionization probe response becomes a means to locate the end-gas region. Knowledge of the location of the last ionization probe to detect the normal flame can then be used to infer where, within the end-gas region, autoignition first occurred.

Normal motion of the lower limbs is discussed in this paper. The biomechanics of human gait has been studied experimentally using an instrumented walkway and analytically by means of mathematical models. Experimental methods for measuring ground reaction forces and limb kinematics are discussed. If limb kinematics are known, they can be used to compute the resultant joint forces and moments, using equations of motion which are algebraic in form. To obtain limb kinematics from the differential equations of motion, the problem is generally redundant, the degree of redundancy being equal to the number of unknown joint moments. The computation of muscle, ligament and bone contact forces from known resultant loads is also a redundant problem because there are more unknowns than there are available equations. For these there is no general consensus regarding the best objective function to be minimized.

A review of the existing mathematical models of a car occupant in a rear-end crash reveals that existing models inadequately describe the kinematics of the occupant and cannot demonstrate the injury mechanisms involved. Most models concentrate on head and neck motion and have neglected to study the interaction of the occupant with the seat back, seat cushion, and restraint systems. Major deficiencies are the inability to simulate the torso sliding up the seat back and the absence of the thoracic and lumbar spine as deformable, load transmitting members. The paper shows the results of a 78 degree-of-freedom model of the spine, head, and pelvis which has already been validated in +Gz and -Gx acceleration directions. It considers automotive-type restraint systems, seat back, and seat cushions, and the torso is free to slide up the seat back.

The biodynamic response of cadaver torsos subjected to -Gx impact acceleration is discussed in this paper, with particular emphasis on the response of the vertebral column. The existence of an axial force along the spine and its manifestation as a load on the seat pan are reported. Spinal curvature appears to be an important factor in the generation of this spine load. In anthropometric dummies, the spine load does not exist. Details of the testing and results are given, and the development of a mathematical model is shown.

The head acceleration pulses obtained from monkey concussion, cadaver skull fracture (t = 0.002 sec), and football helmet experiments (0.006< t< 0.011 sec) have been subjected to injury hazard assessment by the Severity Index method. Although not directly applicable, the method correlates well with degree of monkey concussion. The range of Severity Indices for acceleration pulses obtained during impact to nine cadavers, all of which produced a linear fracture, was 540-1760 (1000 is danger to life) with a median value of 910. The helmet experiments showed good correlation between the Severity Index and the Wayne State University tolerance curve. These helmet tests also showed that a kinematics chart with curves of velocity change, stopping distance, average head acceleration, and time, with a superimposed Wayne State tolerance curve, can be useful in injury assessment.